Laminating Application Tape and HotMask

Stick It In Reverse

How you apply an application tape to a vinyl graphic or a HotMask™ transfer tape to a printed heat transfer applique can affect the appearance of the finished product. If you get wrinkles or bubbles in the paper application tape, I can just about guarantee that you will get wrinkles and bubbles in the applied vinyl.

You don’t believe me? The next time that you wrinkle the application tape or entrap a bubble, remove the release liner from the vinyl and look at the adhesive side of the film. You will see that wrinkles and bubbles have already started to form. At this point, no matter how accomplished you are as an installer, the wrinkles and bubbles have already formed and you will transfer them to the application surface. The good news is that the tiny bubbles will usually breathe out through the film. And if you get a big bubble, you can easily pop those with a pin and press them flat with your thumb. When you get wrinkles, it is a whole different story. Wrinkles are there forever. That’s because a wrinkle occurs when the vinyl sticks to itself.

Applying HotMask™ transfer tape is equally important. If you entrap a bubble in the film over a printed applique, the shape of the air inclusion could manifest itself in a telltale impression after the applique is heat pressed. Impressions of these inclusions are very apparent over the dark areas of a print.

The best way to apply application tape on a graphic is with a laminator. But what do you do if you don’t have one and you have to apply the tape by hand? Applying a tape to a large graphic can be challenging. There is, however, an easy way to get the job done with a minimum of problems. I call this method “stick it in reverse”. Here’s how to do it:

· The first step to preventing bubbles from forming is to always work on a perfectly smooth work surface. When I worked for fleet graphics companies, we always worked on glass covered tables. If you are working on an old wooden tabletop covered with cut marks, you will likely generate bubbles.

· Unwind the application tape or HotMask™ so that the adhesive side of the tape faces upwards and the facestock is against your work surface.

· Turn the weeded graphics so that the vinyl film faces down and lay the graphics panel on top of the sticky side of the application tape. See the photo below.



· Starting in the center of the graphics panel, use your plastic squeegee to laminate the film to the application tape or HotMask™. Starting in the center of the graphic, squeegee one side and then the other. To prevent bubbles form forming between the tape and graphics, apply firm squeegee pressure and overlap your strokes. See the photo below.


· After completing the first step in the laminating process, turn the graphics panel over so the application paper or HotMask™ film is on top. To complete the laminating process, use the plastic squeegee to resqueegee the entire graphic. See the photo below.


Blog Categories


Recent Posts

With the right film, the right application tools and the right techniques, vinyl graphics can be applied to textured wall surfaces such brick and concrete block. Many of old time decal applicators would heat a cast vinyl with an industrial heat gun, and burnish the hot, pliable film into the textured surface using a rivet brush for this job. Read more


The plethora of terms used for the application tapes sold in the sign and screen print markets could confuse anyone. In the sign market, many people just use the terms “application tape” or “application paper”. Frequently this tape is also incorrectly referred to as “transfer tape”.
If you are a purist and want to pick a few nits, the terms application tape and transfer tape refer to completely different products. Transfer tape refers to a transfer adhesive, which is an adhesive coated onto a release liner.

Read more


Many shops, which have printed wall murals in which the ink bleeds to the edge of the panel, have experienced edge curl issues with a variety of vinyl films. For permanent wall graphics applications, I would consider using Arlon’s DPF 8000 film. DPF 8000 is a 3.5 mil (90 micron) satin white calendered vinyl, designed for long term indoor and outdoor applications. It features an aggressive, permanent pressure-sensitive adhesive that sticks to those “hard-to-stick-to” surfaces.
Read more


View All