Installation Instructions: Pre-Pasted VirtuWall™ Wallcovering

VirtuWall™ is a printable latex saturated wallcovering paper that can be used for a wide range of creative and promotional indoor applications. VirtuWall™ is easily installed on walls or other rigid surfaces. Refer to the instructions below when installing VirtuWall™ pre-pasted wallcovering to painted drywall. If applying to a different type of surface, contact RTape for instructions.

Before beginning your installation, gather the following tools:

  • Hand pump pressure spray bottle filled with water
  • Measuring tape
  • Level
  • Straightedge
  • Pencil
  • Utility knife
  • Smoothing brush

Surface Preparation

Proper surface preparation is essential for a quality installation.

  • Walls must be smooth, clean and free of mold, mildew, grease or other stains.
  • If you are installing over existing paint or primer, make sure that the paint or primer has good adhesion to the drywall surface. If freshly painted, make sure to allow 72 hours for the paint to cure to the wall. While high quality primers will provide a good surface, we recommend the following products:
    • Benjamin Moore Fresh Start® Latex Primer
    • Sherwin-Williams® Multi-Purpose Latex Primer
  • Any mold or mildew on a wall may be an indication of a moisture problem. If mold is present, it must be removed from the wall and any moisture accumulation sources must be corrected prior to installation.
  • Fix any imperfections on the wall with either spackling or drywall compound. Prime and seal the wall before applying VirtuWall™.
  • Remove stains and marks such as ballpoint ink, grease, lipstick, crayon, marking pens, or inks from the wall.

Adhesion Selection

There is no need for additional adhesive because the pre-pasted material has a water activated paste. If you choose to use a pre-pasted activator, we recommend Zinsser® SureGrip 120 Activator for Pre-Pasted Wallpaper. This will allow for more "open-time" of the adhesive during installation.


  • Allow for a 1/2" overlap of the material to match up properly with the seams. Compensate for the overlap when setting up the RIP prior to printing.
  • Spray water to the back of the sheet until thoroughly saturated. If using SureGrip®120 Activator, do not spray any water to the back of the sheet. Gently fold the sheet with the adhesive facing each other to keep moist and allow adhesive paste to active. Set aside for 3 minutes.
  • Unfold the sheet and place onto a wall from top to bottom. Carefully smooth out bubbles and crease using a broad smoothing brush starting in the middle of the sheet and brushing outward.
  • If necessary, continue spraying the edges with water throughout the entire process. Allow the surface to dry to the touch then wipe off any excess adhesive using a damp cloth or sponge. Wait for the mural to dry completely before trimming off any excess material. Use a straight knife with a fresh new blade when trimming.
  • Do not install VirtuWall™ unless the installation and storage areas are above 65ºF for at least 48 hours prior to and after installation.


This material is dry strippable if installed using these instructions and recommendations. Start at the top of the image and peel a 6-8" section of the panel completely. Continue drawing the product back on itself at a 180º angle. In instances where the substrate appears to be very tightly bonded to the surface, spray the section with water. After moistening the surface, allow the mural to stand for 60-90 seconds and then return to peeling the mural back upon itself. Use a wet cloth to remove anything remaining on the wall.

Blog Categories

Recent Posts

Whether you are installing trailer graphics or doing a full wrap of a car or van, surface preparation involves a three-step process of detergent washing, solvent cleaning and a final wipe down with IPA. Read more

Whether you are screen printing or painting, the coating must bond to the substrate for the service life of the product. Depending on the physical properties of the coating that you have selected for a project and the substrate to which the coating will be applied, the paint or ink adheres in a few different manners. Read more

Adhesion failures of pressure sensitive materials, such as labels, decorative films, foam tapes and graphic panels, to powder coated substrates are quite common. Just as there are several reasons for these failures, there are several steps that the fabricator can take to avoid these problems. Read more

View All